קונפיגורציות IP

This document describes the IP configuration used at events, both on the fields and in the pits, potential issues, and workaround configurations.

TE.AM IP Address Notation

The notation TE.AM is used as part of IPs in numerous places. This notation refers to splitting your five digit team number into digits for the IP address octets. Where AM is the last two digits of the team number, and TE is the first three digits. Leading zeros are optional. This scheme supports team numbers up to 25599.

למשל: 10.TE.AM.2

Team 1 - 10.0.1.2

קבוצה 12 - 10.0.12.2

קבוצה 122 - 10.1.22.2

Team 1002 - 10.10.2.2

קבוצה 1212 - 10.12.12.2

קבוצה 1202 - 10.12.2.2

קבוצה 1220 - 10.12.20.2

קבוצת 3456 - 10.34.56.2

Team 10000 - 10.100.0.2

Team 12345 - 10.123.45.2

DHCP configuration

This section describes networking when using DHCP to assign IP addresses on the field, in the pits, and at home.

קונפיגורצית DHCP במגרש

Both the Field Network and Robot Radio run DHCP servers with non-overlapping pools. The Field Network DHCP server provides an IP address for the Driver Station, and the Robot Radio provides IP addresses for devices onboard the robot. The IP ranges, subnet mask, and default gateway are listed in the table below.

Field Network

Robot Radio

DHCP Range

10.TE.AM.20 to 10.TE.AM.199

10.TE.AM.200 to 10.TE.AM.219

Subnet Mask

255.255.255.0

255.255.255.0

Default Gateway

10.TE.AM.4

10.TE.AM.4 (10.TE.AM.1 if using the OpenMesh radio)

  • Vivid-Hosting VH-109 Robot Radio - Static 10.TE.AM.1 programmed by Kiosk

  • roboRIO - משוייך על ידי ה-Robot Radio ל-10.TE.AM.2

  • Driver Station - DHCP (”Obtain an IP address automatically“) 10.TE.AM.X assigned by field

  • Other devices (if used) - DHCP 10.TE.AM.YY assigned by Robot Radio

קונפיגורצית DHCP בפיטים

  • VH-109 radio - Static 10.TE.AM.1 programmed by Kiosk.

  • roboRIO - 10.TE.AM.2, מוקצה על ידי ה-Robot Radio

  • Driver Station - DHCP (”משיג כתובת IP באופן אוטומטי“), 10.TE.AM.X, מוקצה על ידי ה-Robot Radio

  • Other devices (if used) - DHCP, 10.TE.AM.Y, assigned by Robot Radio

הערה

If the roboRIO is not being assigned a DHCP IP address of 10.TE.AM.2, ensure you’ve Set the roboRIO team number

At Home DHCP Configuration

  • VH-109 radio - Static 10.TE.AM.1 programmed when configuring robot radio

  • roboRIO - 10.TE.AM.2, מוקצה על ידי ה-Robot Radio

  • VH-109 access point radio - Static 10.TE.AM.4, programmed when configuring access point radio

  • Driver Station - DHCP (”משיג כתובת IP באופן אוטומטי“), 10.TE.AM.X, מוקצה על ידי ה-Robot Radio

  • Other devices (if used) - DHCP, 10.TE.AM.Y, assigned by Robot Radio

הערה

If the roboRIO is not being assigned a DHCP IP address of 10.TE.AM.2, ensure you’ve Set the roboRIO team number

Static Configuration

It is also possible to configure static IPs on your devices to accommodate devices or software which do not support mDNS. When doing so you want to make sure to avoid addresses that will be in use when the robot is on the field network. These addresses are 10.TE.AM.1 for the VH-109 radio, 10.TE.AM.3 and 10.TE.AM.4 for the field network, and anything 10.TE.AM.20 or greater which may be assigned to a device configured for DHCP or else reserved. The roboRIO network configuration can be set from the webdashboard.

  • VH-109 radio - Static 10.TE.AM.1 programmed when configuring robot radio

  • roboRIO - Static 10.TE.AM.2 subnet mask of 255.255.255.0 (default)

  • VH-109 access point radio - Static 10.TE.AM.4, programmed when configuring access point radio

  • Driver Station - Static 10.TE.AM.5 subnet mask must be 255.0.0.0 to enable the DS to reach both the robot and FMS Server, without additionally configuring the default gateway. If a static address is assigned and the subnet mask is set to 255.255.255.0, then the default gateway must be configured to 10.TE.AM.4.

  • Other devices - Static 10.TE.AM.6-.19 subnet 255.255.255.0